Status
This is a known issue (see #15 ). The fix in V3.1.0.0 does not work.
Reported by @AlanHakua. Pinging @skylarkning for verification.
Product
EFIS Cube
Bridge Version
V3.1.0.1
Firmware Version
Latest firmware
Simulator
MSFS 2024
Aircraft/Add-on
iniBuilds A350
Issue
When using the Wingflex EFIS Cube with iniBuilds A350 on Bridge V3.1.0.1, the physical EFIS range selector still prevents aircraft's EFIS range mode from staying in the ZOOM position.
This occurs when the physical EFIS Cube range selector is set to 10NM. If the aircraft EFIS range mode is manually adjusted to ZOOM, ND will successfully enters ZOOM mode. However, if user continues to scroll the aircraft knob to zoom in, the aircraft EFIS range selector is forced back to 10NM position, making ND Zoom function impossible to use.
Steps to Reproduce
- Launch MSFS2024
- Load iniBuilds A350
- Open Wingflex Bridge V3.1.0.1
- Connect the Wingflex EFIS cube
- Select 10NM range at EFIS cube
- Select EFIS range mode to ZOOM in the aircraft
- Attempt to scroll the aircraft knob to zoom in
- Observe whether the zoom mode remains active
Expected Result
The aircraft EFIS panel should have higher priority when EFIS range selector is manually set to ZOOM.
User should be able to select and remain EFIS range to ZOOM mode. When zooming in or out the airport map, EFIS Cube should not force the range back to 10NM hardware position.
Actual Result
When zooming in the airport map, the EFIS Cube forces hardware state synchronization, preventing ZOOM mode from remaining active.
Workaround
Rolling back to bridge version V2.5.1.13 resolves this issue.
Alternatively, manually disabling all EFIS Cube input in V3.1.0.1 Bridge software.
Video Evidence
The video will post at Official QQ group.
Notes
The older bridge software V2.5.1.13 does not have this issue. In my testing, all V3.0 versions fail to handle the ND ZOOM function correctly. Issue #15 did not fix this problem.
Status
This is a known issue (see #15 ). The fix in V3.1.0.0 does not work.
Reported by @AlanHakua. Pinging @skylarkning for verification.
Product
EFIS Cube
Bridge Version
V3.1.0.1
Firmware Version
Latest firmware
Simulator
MSFS 2024
Aircraft/Add-on
iniBuilds A350
Issue
When using the Wingflex EFIS Cube with iniBuilds A350 on Bridge V3.1.0.1, the physical EFIS range selector still prevents aircraft's EFIS range mode from staying in the ZOOM position.
This occurs when the physical EFIS Cube range selector is set to 10NM. If the aircraft EFIS range mode is manually adjusted to ZOOM, ND will successfully enters ZOOM mode. However, if user continues to scroll the aircraft knob to zoom in, the aircraft EFIS range selector is forced back to 10NM position, making ND Zoom function impossible to use.
Steps to Reproduce
Expected Result
The aircraft EFIS panel should have higher priority when EFIS range selector is manually set to ZOOM.
User should be able to select and remain EFIS range to ZOOM mode. When zooming in or out the airport map, EFIS Cube should not force the range back to 10NM hardware position.
Actual Result
When zooming in the airport map, the EFIS Cube forces hardware state synchronization, preventing ZOOM mode from remaining active.
Workaround
Rolling back to bridge version V2.5.1.13 resolves this issue.
Alternatively, manually disabling all EFIS Cube input in V3.1.0.1 Bridge software.
Video Evidence
The video will post at Official QQ group.
Notes
The older bridge software V2.5.1.13 does not have this issue. In my testing, all V3.0 versions fail to handle the ND ZOOM function correctly. Issue #15 did not fix this problem.